Kool Roof |
Premium White Elastomeric Roof Coating |
DESCRIPTION: Kool Roof Bright White Elastomeric Coating is a premium grade, water-based, acrylic elastomeric, “rubber-like” roof coating. By enhancing this product with ceramic; abrasion resistance, durability and life expectancy are greatly increased. When properly applied as part of the Kool Roof Coating System, this product is highly resistant to cracking, chalking, mildew and discoloration. Easily applied with brush, roller or airless spray equipment; it provides a highly protective barrier which will reflect the damaging heat and destructive UV rays from the sun. High solar reflectance can have a significant effect on reducing roof temperatures, which can lead to a reduction of interior temperatures. Kool Roof should be considered an investment that
can pay for itself by extending the useful life of your roof and reducing your cooling costs. |
SURFACE PREPARATION: All unnecessary and non-functional equipment must be removed from the roof. The substrate must be pressure washed ( Kool Roof Roof Wash). A minimum working pressure of 1,500 psi should be used to remove all dirt, dust and previous paints & coatings, which are delaminating. Thoroughly rinse roof surface after cleaning. A standard agricultural pump-up sprayer can be used along with a deck brush to clean the roof, after which the roof must be thoroughly rinsed with clean water. Do not allow Kool Roof Roof Wash to dry on the roof. If the roof has an excess amount of oil or grease, scrubbing with a deck brush may be needed. |
PRIMING: All surfaces are to be primed first to promote the long- term performance of the Kool Roof System. Non-metal surfaces are to be primed with Kool Roof .
Roof Prime This deep penetrating sealant will flow into cracks and crevices of concrete, capsheet, asphalt, masonry, BUR, single-ply and other aged roofing materials. Metal surfaces are to be primed with Kool Roof Metal Primer, which is a zinc rich, red iron oxide metal primer. |
PATCHING and REPAIRS: Patching and repairs are to be made using Kool Roof Brushable Caulk and Kool Roof Poly4. Kool Roof Brushable Caulk is a brush grade acrylic elastomeric caulk. It is applied with a paint brush which can be used alone or to encapsulate the Kool Roof Poly4. Kool Roof Poly4 is a polyester reinforcing fabric that is used to make repairs to gaps larger than 1/8 inch or other problem areas such as, seams, flashing, fasteners, vent stacks, chimneys, skylights, splits, cracks, gaps and holes. |
| Item number |
Size / packaging |
Ship weight |
Units per pallet |
|
| KR.KR1.02T |
2.5 gal / 2 pails |
59 lbs |
45 cases |
| KR.KR1.05T |
5 gal / 1 bucket |
59 lbs |
36 buckets |
| KR.KR1.50T |
50 gal / 1 drum |
659 lbs |
4 Drums |
|
|
| Before proceeding: Choose the morning of a warm day to apply the Kool Roof System. Apply with a 3/4” long nap exterior roller or medium bristle latex paint brush. Apply an initial coat over all seams, joints and repaired areas. Allow to dry for one hour and then apply two (2) uniform coats over the entire roof surface, avoiding excessive rolling. A minimum of two (2) coats are needed for all applications. Apply the second coat perpendicular to the first coat. Allow at least 24 hours between coats. DO NOT apply to any areas where ponding water exists. This product can also be applied with airless spray equipment, 3,000 psi .631 tip. NOTE: If the roof becomes too hot (over 95°F/ 35°C) during application, it is recommended to delay further application until the next morning when surface temperatures are cooler. Excessive roof temperatures may cause blistering of the coating. |
| APPLICATION RATES: (dependent on surface texture & porosity) |
Metal (corrugated) |
80 sq.ft./gal |
| Metal (smooth) |
100 sq.ft./gal |
| Capsheet |
50 sq.ft./gal |
| Asphalt |
50 sq.ft./gal |
Concrete |
50 sq.ft./gal |
|
| COLOR TINTING : This coating can be tinted to light/ pastel shades using 3-4 ounces per gallon of a Universal Colorant System. NOTE: Color tinting will void warranty. |
PRECAUTIONS: Surface to be coated must be clean, dry and mechanically sound. The roof must have positive drainage, NO PONDING WATER AREAS. Roof surface temperatures must be between 50°F -90°F (10°C -32°C). DO NOT apply if heavy fog, dew or rain is expected within 24 -48 hours of application. DO NOT apply within 4 hours of sun set. Low temperatures and humidity will increase dry times. DO NOT allow liquid coating to freeze. It is recommended that UV resistant sunglasses are used during application. When transporting product, ensure lids are sealed and containers are upright. DO NOT heat sealed container or store where temperatures reach or exceed 120°F (48°C). DO NOT allow containers to tumble or roll around as this may cause lids to loosen and leakage to occur. DO NOT transport on passenger seats or inside passenger area of vehicle; transport product in cargo area of vehicle. Not recommended for areas where foot traffic may occur. |
|
|
| FIRST AID -KEEP OUT OF THE REACH OF CHILDREN: If swallowed, do not induce vomiting. Seek medical attention immediately. If contact with skin, wash with soap and water. Apply skin cream if irritation results. If contact with eyes, immediately flush eyes with clean water for 15 minutes. Seek medical attention if irritation persists. |
Kool Roof
|
PROPERTY |
RESULTS |
Volume Solids
ASTM D2697
|
60+ /2% |
Weight Solids
ASTM D1644
|
67+ /1% |
Density |
11.58 + /- .1 lb/ gal |
pH |
>8.5 |
Viscosity |
25,000 + /- 2,000 cps |
Tensile Strength
ASTM D2370
|
240 psi |
Elongation
ASTM D2370
|
600% |
Permanence
ASTM D1653A
|
43 perms |
Water Swelling
ASTM D471
|
10% |
Accl. Weathering
ASTM D4798
|
No cracking or splitting |
Wet Adhesion
ASTM C794
|
3.0 pli (concrete) |
Dry Adhesion
ASTM C794
|
9.0 pli (concrete) |
Fungi Resistance
ASTM G21
|
Passes |
Low Temp. Flex.
ASTM D522
|
Passes |
Vehicle/ solvent |
Water |
V.O.C 50 grams per liter |
| |
| Water |
CAS# 7732-18-5 |
| Titanium |
CAS# 13463-67-7 |
| Calcium Carbonate |
CAS# 1317-65-3 |
| Zinc Oxide |
CAS# 1314-13-2 |
| Ceramic |
CAS# 65997-17-3 |
| Acrylic Resin |
Trade Secret |
| Emergency Telephone: INFOTRAC - (800)535-5053 |
|
| STORAGE, CLEAN-UP and DISPOSAL: Store unused product in its original, tightly sealed container. Clean tools, hands and small spills with soap and water while wet. Dispose of all containers in accordance with state and local governmental regulations. |
| LIMITED WARRANTY: This product is warranted to be free of manufacturers defects for a period of ten (10) years from the date of purchase, when used as part of the Kool Roof System and applied according to our written specifications. If this coating does not perform as stated during this warranty period, Advanced Coating Systems, Inc. will provide the original purchaser with original sales receipt, replacement coating to repair the affected part of the roof on a prorated basis and does not include labor, freight or other materials mentioned or bearing the cost thereof. |
| Our suggested installation specification are based on information for laboratory and field testing, which we believe to be reliable and correct; however, accuracy and completeness of said tests are not guaranteed and not to be construed as a warranty, either express or implied. Since the use of the material is beyond the manufacturers control, buyer assumes all risks whatsoever as to their use or results obtained. We guarantee our products to confirm to Advanced Coating Systems, Inc. quality control. Advanced Coatings Systems, Inc. warrants only the standard quality of material. Manufacturers sole responsibility shall be to replace that portion of the product which is proven to be defective. |
| Advanced Coating Systems, Inc. makes no other warranty of any kind whatsoever expressed or implied as to the description, quality, merchantability or fitness of any particular purpose and under no circumstances is said manufacturer responsible for incidental or consequential damages of any kind to the building upon which the roof is affixed or its contents, loss of rent or profit or any inconvenience. Neither seller nor manufacturer shall be liable of any injury arising from the use of or inability to use the product. There is no express warranties which extend beyond the description on the face there of. Installer is responsible to check the adhesion and compatibility of all Kool Roof products prior to application. |
 |
|
