Brush Caulk |
Acrylic Elastomeric Brushable Caulk |
DESCRIPTION: Kool Roof Brush Caulk is an acrylic, single component, brush grade caulk. It is used as a patching compound for sealing leaks and in general roof maintenance. It is a thick, white acrylic, liquid patching compound that dries to form a “rubber-like” protective membrane. It can be used alone or with Kool Roof Poly4 fabric to make reinforced repairs to damaged areas of a roof. Ideal for patching holes, cracks, gaps, flashing, seams, fasteners, skylights, vents and other roof penetrations. |
SURFACE PREPARATION: All unnecessary and nonfunctional equipment must be removed from the roof. Remove loose flaking rust, loose paint or coatings with wire brush or high power pressure washing. The substrate must be pressure washed ( Kool Roof Roof Wash). A minimum working pressure of 1,500 psi should be used to remove all dirt, dust, previous paints & coatings, which are delaminating. Thoroughly rinse roof surface after cleaning. A standard agricultural pump-up sprayer can be used along with a deck brush to clean the roof, after which the roof must be thoroughly rinsed with clean water. Do not allow Kool Roof Roof Wash to dry on the roof. If the roof has an excess amount of oil or grease. scrubbing with a deck brush may be needed. |
USES: Metal, asphalt, asphalt singles, concrete, brick, Mobile Homes/ RV’s, masonry, built-up, roof tile |
APPLICATION: Choose the morning of a warm day to apply the Kool Roof Brush Caulk. Use a high quality nylon/ polyester brush to apply. |
| |
Kool Roof Brush Caulk |
Kool Roof Brush Caulk can be used alone to seal gaps, crack and small voids less than 1/8 inch wide. Apply Kool Roof Brush Caulk in the direction which best allows it to penetrate deep into the void. Make sure to feather the Kool Roof Brush Caulk at least 4 inches past the area to be repaired.
| Item number |
Size / packaging |
Ship weight |
Units per pallet |
|
| KR.BC1.01T |
1 gal / 4 pails |
48 lbs |
45 cases |
| KR.BC1.05T |
5 gal / 1 bucket |
60 lbs |
36 buckets |
|
|
Kool Roof Brush Caulk with
Kool Roof Poly4 reinforcing fabric |
| Kool Roof, Brush Caulk can be used with Poly4 fabric to act as a reinforced bandage to repair problem areas of a roof. Apply a thin layer of Kool Roof, Brush Caulk in the direction which best allows it to penetrate deep into the void. Make sure to feather the Kool Roof Brush Caulk at least 4 inches past the area to be repaired. Cut an appropriate length of Kool Roof Poly4 Fabric to make the repair. Place the Kool Roof Poly4 onto the wet Kool Roof Brush Caulk, make sure there are no wrinkles, puckers or air trapped under the Kool Roof Poly4 Fabric. Apply a coat of Kool Roof Brush Caulk to the top of the Kool Roof Poly4 Fabric making sure the fabric is completely saturated and smooth. Feather the Kool Roof Brush Caulk 4 inches beyond the Kool Roof Poly4 Fabric. |
| DRY TIME: Dries to the touch in 1 hour @ 77°F (25°C) at 50% humidity. Kool Roof Brush Caulk is a water-based coating, dry times may be longer if temperature is cooler and humidity is higher. |
| APPLICATION RATES: (dependant on surface texture & porosity) |
| Approximately 12.5 square feet per gallon at a film thickness of 1/8 inch. |
| PRECAUTIONS: Surface to be coated must be clean, dry and mechanically sound. The roof must have positive drainage, NO PONDING WATER AREAS . Roof surface temperatures must be between 50°F -90°F (10°C -32°C). DO NOT apply if heavy fog, dew or rain is expected within 24 -48 hours of application. DO NOT apply within 4 hours of sun set. Low temperatures and humidity will increase dry times. DO NOT allow liquid coating to freeze. It is recommended that UV resistant sunglasses are used during application. When transporting product ensure lids are sealed and containers are upright. DO NOT heat sealed container or store where temperatures reach or exceed 120°F (48°C). DO NOT allow containers to tumble or roll around as this may cause lids to loosen and leakage to occur. DO NOT transport on passenger seats or inside passenger area of vehicle; transport product in cargo area of vehicle. Not recommended for areas where foot traffic may occur. |
|
|
| FIRST AID -KEEP OUT OF THE REACH OF CHILDREN: If swallowed, do not induce vomiting. Seek medical attention immediately. If contact with skin, wash with soap and water. Apply skin cream if irritation results. If contact with eyes, immediately flush eyes with clean water for 15 minutes. Seek medical attention if irritation persists. |
Brush Caulk
|
PROPERTY |
RESULTS |
Color |
White |
Volume Solids
ASTM D2697
|
28+ /2% |
Weight Solids
ASTM D1644
|
62+ /1% |
Density |
11.5 + /- .1 lb/ gal |
pH |
>8.8 + /- .5 |
Viscosity |
31,000 + /- 4,000 cps |
Tensile Strength
ASTM D2370
|
235 psi |
Elongation
ASTM D2370
|
200% |
Permanence
ASTM D1653A
|
5 perms |
Fungi Resistance
ASTM G21
|
Passes |
Accl. Weathering
ASTM D4798
|
No cracking or splitting |
Flexibility
ASTM D522
|
Pass |
Coverage |
12.5 sq.ft./ Gal. 1/8” thick |
Flash Point |
Same as water |
Vehicle/ solvent |
Water |
V.O.C .5 grams per liter |
| |
| Water |
CAS# 7732-18-5 |
| Titanium |
CAS# 13463-67-7 |
| Calcium Carbonate |
CAS# 1317-65-3 |
| Zinc Oxide |
CAS# 1314-13-2 |
| Acrylic Resin |
Trade Secret |
| Emergency Telephone: INFOTRAC - (800)535-5053 |
|
| STORAGE, CLEAN-UP and DISPOSAL: Store unused product in its original, tightly sealed container. Clean tools, hands and small spills with soap and water while wet. Dispose of all containers in accordance with state and local governmental regulations. |
| LIMITED WARRANTY: This product is warranted to be free of manufacturers defects for a period of seven (7) years from the date of purchase, when used as part of the Kool Roof System and applied according to our written specifications. If this coating does not perform as stated during this warranty period, Advanced Coating Systems, Inc. will provide the original purchaser with original sales receipt, replacement coating to repair the affected part of the roof on a prorated basis and does not include labor, freight or other materials mentioned or bearing the cost thereof. |
| Our suggested installation specification are based on information for laboratory and field testing, which we believe to be reliable and correct; however, accuracy and completeness of said tests are not guaranteed and not to be construed as a warranty, either express or implied. Since the use of the material is beyond the manufacturers control, buyer assumes all risks whatsoever as to their use or results obtained. We guarantee our products to confirm to Advanced Coating Systems, Inc. quality control. Advanced Coatings Systems, Inc. warrants only the standard quality of material. Manufacturers sole responsibility shall be to replace that portion of the product which is proven to be defective. |
| Advanced Coating Systems, Inc. makes no other warranty of any kind whatsoever expressed or implied as to the description, quality, merchantability or fitness of any particular purpose and under no circumstances is said manufacturer responsible for incidental or consequential damages of any kind to the building upon which the roof is affixed or its contents, loss of rent or profit or any inconvenience. Neither seller nor manufacturer shall be liable of any injury arising from the use of or inability to use the product. There is no express warranties which extend beyond the description on the face there of. Installer is responsible to check the adhesion and compatibility of all Kool Roof products prior to application. |
| |
|
