Roof Prime |
All Purpose Clear Primer |
DESCRIPTION: Kool Roof Roof Prime is a durable clear primer for use on non-rusted surfaces. It acts as an intermediate base coat for the Kool Roof Bright White Elastomeric Roof Coating. Kool Roof Roof Prime is a water-based coating which exhibits superior adhesion to various substrates, has a quick drying time, environmentally safe and cleans up with soap and water. |
SURFACE PREPARATION: All unnecessary and nonfunctional equipment must be removed from the roof. The substrate must be pressure washed ( Kool Roof Roof Wash). A minimum working pressure of 1,500 psi should be used to remove all dirt, dust and previous paints & coatings, which are delaminating. Thoroughly rinse roof surface after cleaning. A standard agricultural pump-up sprayer can be used along with a deck brush to clean the roof, after which the roof must be thoroughly rinsed with clean water. Do not allow Kool Roof Roof Wash to dry on the roof. If the roof has an excess amount of oil or grease. scrubbing with a deck brush may be needed. |
USES: Concrete, single-ply, capsheet, masonry, brick, block, BUR, asphalt, wood, Hypalon, EPDM, Hardiplank, polyurethane foam, Transite |
APPLICATION: Choose the morning of a warm day to apply the Kool Roof Roof Prime. Use either a high quality ½” nap roller cover, nylon/ polyester brush or an airless sprayer (.017 spray tip). Stir primer occasionally. DO NOT THIN. Two coats may be needed over very porous surfaces. Allow to dry completely before topcoating with Kool Roof Bright White Elastomeric Coating. |
| Item number |
Size / packaging |
Ship weight |
Units per pallet |
|
| KR.RP1.01T |
1 gal / 4 pails |
50 lbs |
45 cases |
| KR.RP1.05T |
5 gal / 1 bucket |
62 lbs |
36 buckets |
| KR.RP1.50T |
50 gal / 1 drum |
625 lbs |
4 Drums |
|
|
| DRY TIME: Dries to the touch in 1 hour @ 77°F (25°C) at 50% humidity. Kool Roof Roof Prime is a water-based coating, dry times may be longer if temperature is cooler and humidity is higher. |
| APPLICATION RATES: (dependent on surface texture & porosity) |
Shingle |
100 sq.ft./gal |
| Capsheet |
100 sq.ft./gal |
| Asphalt |
125 sq.ft./gal |
| Concrete |
200 sq.ft./gal |
| EPDM |
200 sq.ft./gal |
| Transite |
100 sq.ft./gal |
|
PRECAUTIONS: Surface to be coated must be clean, dry and mechanically sound. The roof must have positive drainage, NO PONDING WATER AREAS. Roof surface temperatures must be between 50°F -90°F (10°C -32°C). DO NOT apply if heavy fog, dew or rain is expected within 24 -48 hours of application. DO NOT apply within 4 hours of sun set. Low temperatures and humidity will increase dry times. DO NOT allow liquid coating to freeze. It is recommended that UV resistant sunglasses are used during application. When transporting product, ensure lids are sealed and containers are upright. DO NOT heat sealed container or store where temperatures reach or exceed 120°F (48°C). DO NOT allow containers to tumble or roll around as this may cause lids to loosen and leakage to occur. DO NOT transport on passenger seats or inside passenger area of vehicle; transport product in cargo area of vehicle. Not recommended for areas where foot traffic may occur. |
|
|
| FIRST AID -KEEP OUT OF THE REACH OF CHILDREN: If swallowed, do not induce vomiting. Seek medical attention immediately. If contact with skin, wash with soap and water. Apply skin cream if irritation results. If contact with eyes, immediately flush eyes with clean water for 15 minutes. Seek medical attention if irritation persists. |
Roof Prime
|
PROPERTY |
RESULTS |
Color |
White, dries clear |
Volume Solids
ASTM D2697
|
21 +/- 2% |
Weight Solids
ASTM D1644
|
32 + /- 1% |
Density |
9.4 + /- .1 lb/ gal |
pH |
>8.5 + /- .5 |
Viscosity |
7,000 + /- 1,000 cps |
Tensile Strength
ASTM D2370
|
240 psi |
Elongation
ASTM D2370
|
400% |
Permanence
ASTM D1653A
|
13 perms |
Flash Point |
Same as water |
Boiling |
212°F (100°C) |
Min. Surface Temp. |
50°F (10°C) |
Coverage |
Dependent on surface Condition |
Dry Time |
1 hr. 77°F (25°C)@ 50% humidity |
Vehicle/ solvent |
Water |
V.O.C 122 grams per liter |
| |
| Water |
CAS# 7732-18-5 |
| Titanium |
CAS# 13463-67-7 |
| Calcium Carbonate |
CAS# 1317-65-3 |
| Zinc Oxide |
CAS# 1314-13-2 |
| Ammonium Hydroxide |
CAS# 1336-21-6 |
| Ethylene Glycol |
CAS# 107-21-1 |
| Emergency Telephone: INFOTRAC - (800)535-5053 |
|
| STORAGE, CLEAN-UP and DISPOSAL: Store unused product in its original, tightly sealed container. Clean tools, hands and small spills with soap and water while wet. Dispose of all containers in accordance with state and local governmental regulations. |
| LIMITED WARRANTY: This product is warranted to be free of manufacturers defects for a period of seven (7) years from the date of purchase, when used as part of the Kool Roof System and applied according to our written specifications. If this coating does not perform as stated during this warranty period, Advanced Coating Systems, Inc. will provide the original purchaser with original sales receipt, replacement coating to repair the affected part of the roof on a prorated basis and does not include labor, freight or other materials mentioned or bearing the cost thereof. |
| Our suggested installation specification are based on information for laboratory and field testing, which we believe to be reliable and correct; however, accuracy and completeness of said tests are not guaranteed and not to be construed as a warranty, either express or implied. Since the use of the material is beyond the manufacturers control, buyer assumes all risks whatsoever as to their use or results obtained. We guarantee our products to confirm to Advanced Coating Systems, Inc. quality control. Advanced Coatings Systems, Inc. warrants only the standard quality of material. Manufacturers sole responsibility shall be to replace that portion of the product which is proven to be defective. |
| Advanced Coating Systems, Inc. makes no other warranty of any kind whatsoever expressed or implied as to the description, quality, merchantability or fitness of any particular purpose and under no circumstances is said manufacturer responsible for incidental or consequential damages of any kind to the building upon which the roof is affixed or its contents, loss of rent or profit or any inconvenience. Neither seller nor manufacturer shall be liable of any injury arising from the use of or inability to use the product. There is no express warranties which extend beyond the description on the face there of. Installer is responsible to check the adhesion and compatibility of all Kool Roof products prior to application. |
| |
|
